Chemical and Biomolecular Engineering - Research Publications

Permanent URI for this collection

Search Results

Now showing 1 - 5 of 5
  • Item
    Thumbnail Image
    Effects of industrial gas impurities on the performance of mixed matrix membranes
    Kanehashi, S ; Aguiar, A ; Lu, HT ; Chen, GQ ; Kentish, SE (ELSEVIER SCIENCE BV, 2018-03-01)
  • Item
    Thumbnail Image
    Can the addition of carbon nanoparticles to a polyimide membrane reduce plasticization?
    Kanehashi, S ; Chen, GQ ; Danaci, D ; Webley, PA ; Kentish, SE (ELSEVIER SCIENCE BV, 2017-08-07)
  • Item
    Thumbnail Image
    Enhancing gas permeability in mixed matrix membranes through tuning the nanoparticle properties
    Kanehashi, S ; Chen, GQ ; Scholes, CA ; Ozcelik, B ; Hua, C ; Ciddor, L ; Southon, PD ; D'Alessandro, DM ; Kentish, SE (ELSEVIER SCIENCE BV, 2015-05-15)
  • Item
    Thumbnail Image
    The impact of water vapor on CO2 separation performance of mixed matrix membranes
    Kanehashi, S ; Chen, GQ ; Ciddor, L ; Chaffee, A ; Kentish, SE (Elsevier, 2015-10-05)
    A series of mixed matrix membranes (MMMs) using nanoparticles involving carbons, porous organic polymers and metal organic frameworks (MOFs) were prepared to investigate the impact of water vapor on CO2 separation performance. The water uptake of MMMs using hydrophilic MOFs increased relative to more hydrophobic particles such as the porous organic polymers and carbons and this trend was reflected in the water vapor permeability, which varied by a factor of three between the hydrophobic and hydrophilic MMMs. These changes in water vapor permeability were strongly correlated with the water solubility, indicating that it is this solubility that is the controlling parameter. The calculated water diffusivity was consistent with previously published results. The gas permeability of MMMs in the presence of water vapor was also strongly affected by the nanoparticle hydrophobicity, with membranes composed of hydrophobic fillers out-performing hydrophilic fillers of comparable porosity. However in general, the differences in performance between MMMs and the pure polymer narrowed in the presence of water vapor.
  • Item
    Thumbnail Image
    Water vapor permeation through cellulose acetate membranes and its impact upon membrane separation performance for natural gas purification
    Chen, GQ ; Kanehashi, S ; Doherty, CM ; Hill, AJ ; Kentish, SE (Elsevier, 2015-08-01)
    Abstract Cellulose acetate is the predominant material used in membrane separation of acid gases from natural gas and biogas. However, the sensitivity of these membranes to water vapor is not well understood. In this work, flat-sheet membranes of two different degrees of acetylation, were exposed to both dry and humidified CH4 and CO2/CH4 mixtures. Positron Annihilation Lifetime Spectroscopy experiments showed that the number of free volume elements decreased as water concentration increased, indicating pore filling effects. The size of the free volume elements declined initially, followed by an increasing trend at vapor partial pressures greater than 2.5 kPa, indicating polymer swelling. Gas permeabilities of CH4 and CO2 followed a similar trend, with an initial decline due to hindered diffusion and competitive sorption, followed by an increase as the humidity exceeded 2.5 kPa. Water vapor permeabilities increased from 11,000 to 27,000 Barrer as the water activity increased but a change in the rate of increase was also noted at 2.5 kPa. At humidities in excess of 0.8, the extent of membrane swelling was such that equilibrium was not established even after 8 h of operation. Importantly, plasticization had significantly less impact on the polymer with a higher degree of acetylation.