Mechanical Engineering - Research Publications

Permanent URI for this collection

Search Results

Now showing 1 - 6 of 6
  • Item
    Thumbnail Image
    Spatial averaging effects on the streamwise and wall-normal velocity measurements in a wall-bounded turbulence using a cross-wire probe
    Baidya, R ; Philip, J ; Hutchins, N ; Monty, JP ; Marusic, I (IOP Publishing, 2019-08-01)
    The spatial averaging effects due to a cross-wire probe on the measured turbulence statistics in a wall-bounded flow are investigated using a combined approach of direct numerical simulation data, theoretical methods and experiments. In particular, the wire length (l), spacing ( ) and angle ( ) of a cross-wire probe configured to measure the streamwise and wall-normal velocities are systematically varied to isolate effects of each parameter. The measured streamwise velocity from a cross-wire probe is found to be an average of the filtered velocities sensed by the two wires. Thus, in general, an increase in the sensor dimensions when normalised by viscous units leads to an attenuated variance for the streamwise velocity ( ), resulting from a larger contribution to the spatial averaging process from poorly correlated velocities. In contrast, the variance for the wall-normal velocity ( ) can be amplified, and this is shown to be the result of an additional contributing term (compared to ) due to differences in the filtered wire-normal velocity between the two wires. This additional term leads to a spurious wall-normal velocity signal, resulting in an amplified variance recorded by the cross-wire probe. Compared to the streamwise and wall-normal velocity variances, the Reynolds shear stress ( ) perhaps surprisingly shows less variation when l, and are varied. The robustness of Reynolds shear stress to the finite sensor size is due to two effects: (i) Reynolds shear stress is devoid of energetic contributions from the near-isotropic fine scales unlike the and statistics, hence cross-wire probe dimensions are typically sufficiently small in terms of viscous unit to adequately capture the statistics for a range of l and investigated; (ii) the dependency arises due to cross terms between the filtered velocities from two wires, however, it turns out that these terms cancel one another in the case of Reynolds shear stress, but not for the and statistics. We note that this does not, however, suggest that is easier to measure accurately than the normal stresses; on the contrary, in a companion paper (Baidya et al 2019 Meas. Sci. Technol. 30 085301) we show that measurements are more prone to errors due to uncertainty in probe geometry and calibration procedure.
  • Item
    Thumbnail Image
    Sensitivity of turbulent stresses in boundary layers to cross-wire probe uncertainties in the geometry and calibration procedure
    Baidya, R ; Philip, J ; Hutchins, N ; Monty, JP ; Marusic, I (IOP Publishing, 2019-08-01)
    The sensitivity of measured turbulent stresses to uncertainties in the probe geometry and calibration procedure is investigated for a cross-wire probe in a turbulent boundary layer using direct numerical simulation data. The errors investigated are guided by experiments, and to replicate the full experimental procedure, the cross-wire calibration procedure is simulated to generate a voltage-to-velocity mapping function, which is then utilised to calculate the measured velocity from simulated cross-wire voltages. We show that wire misalignment can lead to an incorrect mean wall-normal velocity and Reynolds shear stress in the near-wall region due to the presence of shear. Furthermore, we find that misalignment in the wire orientation cannot be fully accounted for through the calibration procedure, presumably due to increased sensitivity to an out-of-plane velocity component. This has strong implications if using a generic commercial cross-wire probe, since inclining these probes to gain access to the near-wall region can lead to a large error (up to 10%) in turbulent stresses and these errors can manifest in the log region and beyond to half the boundary layer thickness. For uncertainties introduced during the calibration procedure, the Reynolds shear stress is observed to exhibit an elevated sensitivity compared with other turbulent stresses. This is consistent with empirical observations where the repeatability in the Reynolds shear stress is found to be the poorest.
  • Item
    Thumbnail Image
    Spatial averaging of velocity measurements in wall-bounded turbulence: single hot-wires
    Philip, J ; Hutchins, N ; Monty, JP ; Marusic, I (IOP Publishing Ltd, 2013-11)
  • Item
    Thumbnail Image
    Spatial averaging of streamwise and spanwise velocity measurements in wall-bounded turbulence using ν- and x-probes
    Philip, J ; Baidya, R ; Hutchins, N ; Monty, JP ; Marusic, I (IOP PUBLISHING LTD, 2013-11)
  • Item
    Thumbnail Image
    Distance-from-the-wall scaling of turbulent motions in wall-bounded flows
    Baidya, R ; Philip, J ; Hutchins, N ; Monty, JP ; Marusic, I (AIP Publishing, 2017-02)
    An assessment of self-similarity in the inertial sublayer is presented by considering the wall-normal velocity, in addition to the streamwise velocity component. The novelty of the current work lies in the inclusion of the second velocity component, made possible by carefully conducted subminiature ×-probe experiments to minimise the errors in measuring the wall-normal velocity. We show that not all turbulent stress quantities approach the self-similar asymptotic state at an equal rate as the Reynolds number is increased, with the Reynolds shear stress approaching faster than the streamwise normal stress. These trends are explained by the contributions from attached eddies. Furthermore, the Reynolds shear stress cospectra, through its scaling with the distance from the wall, are used to assess the wall-normal limits where self-similarity applies within the wall-bounded flow. The results are found to be consistent with the recent prediction from the work of Wei et al. [“Properties of the mean momentum balance in turbulent boundary layer, pipe and channel flows,” J. Fluid Mech. 522, 303–327 (2005)], Klewicki [“Reynolds number dependence, scaling, and dynamics of turbulent boundary layers,” J. Fluids Eng. 132, 094001 (2010)], and others that the self-similar region starts and ends at z+∼O(δ+) and O(δ+), respectively. Below the self-similar region, empirical evidence suggests that eddies responsible for turbulent stresses begin to exhibit distance-from-the-wall scaling at a fixed z+ location; however, they are distorted by viscous forces, which remain a leading order contribution in the mean momentum balance in the region z+≲O(δ+), and thus result in a departure from self-similarity.
  • Item
    Thumbnail Image
    The quiescent core of turbulent channel flow
    Kwon, YS ; Philip, J ; de Silva, CM ; Hutchins, N ; Monty, JP (CAMBRIDGE UNIV PRESS, 2014-07)
    Abstract The identification of uniform momentum zones in wall-turbulence, introduced by Adrian, Meinhart & Tomkins (J. Fluid Mech., vol. 422, 2000, pp. 1–54) has been applied to turbulent channel flow, revealing a large ‘core’ region having high and uniform velocity magnitude. Examination of the core reveals that it is a region of relatively weak turbulence levels. For channel flow in the range $\def \xmlpi #1{}\def \mathsfbi #1{\boldsymbol {\mathsf {#1}}}\let \le =\leqslant \let \leq =\leqslant \let \ge =\geqslant \let \geq =\geqslant \def \Pr {\mathit {Pr}}\def \Fr {\mathit {Fr}}\def \Rey {\mathit {Re}}Re_{\tau } = 1000\text {--}4000$, it was found that the ‘core’ is identifiable by regions bounded by the continuous isocontour lines of the streamwise velocity at $0.95U_{CL}$ (95 % of the centreline velocity). A detailed investigation into the properties of the core has revealed it has a large-scale oscillation which is predominantly anti-symmetric with respect to the channel centreline as it moves through the channel, and there is a distinct jump in turbulence statistics as the core boundary is crossed. It is concluded that the edge of the core demarcates a shear layer of relatively intense vorticity such that the interior of the core contains weakly varying, very low-level turbulence (relative to the flow closer to the wall). Although channel flows are generally referred to as ‘fully turbulent’, these findings suggest there exists a relatively large and ‘quiescent’ core region with a boundary qualitatively similar to the turbulent/non-turbulent interface of boundary layers, jets and wakes.