Mechanical Engineering - Research Publications
Permanent URI for this collection
Search Results
1 - 10 of 62
-
ItemNo Preview AvailableThe effect of cleaning and repainting on the ship drag penalty(TAYLOR & FRANCIS LTD, 2021-07-01)Although the hull of a recently dry-docked large ship is expected to be relatively smooth, surface scanning and experimentation reveal that it can exhibit an "orange-peel" roughness pattern with an equivalent sand-grain roughness height ks = 0. 101 mm. Using the known ks value and integral boundary layer evolution, a recently cleaned and coated full-scale ship was predicted to experience a significant increase in the average coefficient of friction %ΔC¯f and total hydrodynamic resistance %ΔR¯T during operation. Here the report also discusses two recently reported empirical estimations that can estimate ks directly from measured surface topographical parameters, by-passing the need for experiments on replicated surfaces. The empirical estimations are found to have an accuracy of 4.5 - 5 percentage points in %ΔC¯f.
-
ItemNo Preview AvailableNon-k-type behaviour of roughness when in-plane wavelength approaches the boundary layer thickness(CAMBRIDGE UNIV PRESS, 2021-01-22)Abstract
-
ItemHeat Transfer Coefficient Estimation for Turbulent Boundary Layers(The University of Queensland, 2020-12-11)Convective heat transfer in rough wall-bounded turbulent flows is prevalent in many engineering applications, such as in gas turbines and heat exchangers. At present, engineers lack the design tools to accurately predict the convective heat transfer in the presence of non-smooth boundaries. Accordingly, a new turbulent boundary layer facility has been commissioned, where the temperature of an interchangeable test surface can be precisely controlled, and conductive heat losses are minimized. Using this facility, we can estimate the heat transfer coefficient (Stanton number, St), through measurement of the power supplied to the electrical heaters and also from measurements of the thermal and momentum boundary layers evolving over this surface. These methods have been initially investigated over a shorter smooth prototype heated surface and compared with existing St prediction models. Preliminary results suggest that we can accurately estimate St in this facility.
-
ItemAn investigation of cold-wire spatial resolution using a DNS database(The University of Queensland, 2020-12-11)The effect of spatial resolution of cold-wire anemometry on both the variance and energy spectrum of temperature fluctuations is analyzed through the use of a numerical database. Temperature fluctuation snapshots from a direct numerical simulation (DNS) of a heated smooth-wall turbulent channel flow are spatially averaged in the spanwise direction to simulate the wire filtering. The results show that the wire length does not affect the mean temperature while it significantly attenuates the variance of temperature fluctuations, particularly in the vicinity of the wall. As the filter length grows, the peaks of the one- and two-dimensional energy spectrograms are further attenuated. Limited attenuation is seen when the filter length is smaller than 30 wall units in the vicinity of the wall, whereas a complete suppression of the near-wall energetic peak is observed when the filter length exceeds 100 wall units.
-
Item
-
ItemSimulation of large-eddy-break-up device (LEBU) in a moderate Reynolds number turbulent boundary layer(Springer, 2016-08-11)A well-resolved large eddy simulation (LES) of a large-eddy break-up (LEBU) device in a spatially evolving turbulent boundary layer is performed with, Reynolds number, based on free-stream velocity and momentum-loss thickness, of R e θ ≈ 4300. The implementation of the LEBU is via an immersed boundary method. The LEBU is positioned at a wall-normal distance of 0.8 δ (δ denoting the local boundary layer thickness at the location of the LEBU) from the wall. The LEBU acts to delay the growth of the turbulent boundary layer and produces global skin friction reduction beyond 180δ downstream of the LEBU, with a peak local skin friction reduction of approximately 12 %. However, no net drag reduction is found when accounting for the device drag of the LEBU in accordance with the towing tank experiments by Sahlin et al. (Phys. Fluids 31, 2814, 1988). Further investigation is performed on the interactions of high and low momentum bulges with the LEBU and the corresponding output is analysed, showing a ‘break-up’ of these large momentum bulges downstream of the LEBU. In addition, results from the spanwise energy spectra show consistent reduction in energy at spanwise length scales for λ+z>1000 independent of streamwise and wall-normal location when compared to the corresponding turbulent boundary layer without LEBU.
-
ItemStructure Inclination Angles in the Convective Atmospheric Surface Layer(SPRINGER, 2013-04)
-
ItemThe Effect of Wall Normal Actuation on a Turbulent Boundary Layer(SPRINGER, 2017-12)
-
Item
-
Item